How much do Z purlins cost?
Metal Purlin Pricing Chart
| 14 Gauge, Galvanized | 14 Gauge, Red Oxide | |
|---|---|---|
| 4” X 2” | $2.00- $3.00 Per linear Ft. | $2.00- $2.50 Per linear Ft. |
| 6” X 2” | $3.00- $4.00 Per linear Ft. | $2.50- $3.00 Per linear Ft. |
| 8” X 2.5” | $4.00- $5.00 Per linear Ft. | $3.50- $4.00 Per linear Ft. |
| 10” X 2.5” | $4.50- $5.50 Per linear Ft. | $4.00- $5.00 Per linear Ft. |
How far can you span R panel?
Whether you choose R-Panel/PBR-Panel for its ability to handle slopes as low as 1:12 or open framing spans as far as 5′-7′ apart, R-Panel/PBR-Panel lives up to the demands you place on it.
Can I use 1×4 for purlins?
Kiln-dried softwood is recommended for purlins or decking (pine, fir, hemlock, and spruce). On re-roofing projects where the condition of the old decking is in question, or where existing shingles will be left in place, new 2×4 or 1×4 purlins should be fastened through the decking and into the rafters.
How much does AZ purlin weigh?
Weight: 3.37 Lbs. Per Ft. Zee Purlin is primarily used as structural framework in buildings due to its lightweight and economical properties.
How far can a 2×6 span as a purlin?
Max. Live Load 20 lbs/ft2 (956 N/m2)
| Maximum Span (ft – in) | ||
|---|---|---|
| Nominal Size (inches) | Rafter Spacing, Center to Center, OC (inches) | Lumber Grade |
| 2 x 6 | 12 | 16′ – 4” |
| 16 | 14′ – 11” | |
| 24 | 13′ |
What is the difference between R panel and PBR panel?
R Panel is mainly used for wall or siding applications and PBR panel should be used for a roof or a wall. The cost difference between these two panels is less than 2%, so you will find that many manufacturers usually will only offer PBR panels as they can be used in both roofing and wall applications.
How much does R panel cost?
R Panel will generally cost $2.00-$4.50 per square foot for material….How Much Does R Panel Cost?
| 26 Gauge R-Panel (SMP Paint) | $2.00- $2.50 per sq. ft. |
|---|---|
| 24 Gauge R-Panel (SMP Paint) | $2.50- $3.00 per sq. ft. |
What sizes do you manufacture steel roof purlins?
We manufacture any component from 1/2″ steel subgirts to 12″ section up to 10 gauge. Steel z-purlins and z-girts are also available with other depths and flange widths. Contact Flexospan for information on custom purlin and girt structural steel dimensions. Steel roof purlins and wall girts are produced and available in house.
Why choose flexospan for your metal building projects?
“For many decades, Flexospan has supplied top-quality metal roof and wall panels to steel mills, coal mines, power plants, and other similar industrial operations.” “Metal buildings are our specialty.” Flexospan can help with your metal building maintenance and construction projects!
Where is flexospan metal roofing made?
Many Decades! Flexospan is a metal roofing and siding manufacturer located in northwest Pennsylvania.
Are flexospan panels recyclable?
GREEN / LEED Data – Flexospan panels contain post-consumer recycled content, and are recyclable or biodegradable after use. “For many decades, Flexospan has supplied top-quality metal roof and wall panels to steel mills, coal mines, power plants, and other similar industrial operations.” “Metal buildings are our specialty.”